Arbisol DS100

Packaging: 20K, 4K, 1K, 500g, 250g, 125g
Arbisol DS100 mixed with PRC Red Scarlet.
Arbisol DS100 mixed with PRC Red Scarlet.
Add Arbiair White SC to make white discharge print.
Add Arbiair White SC to make white discharge print.
Prints_Arbisol DS100(02)
Previous image
Next image

Discharge ink base is for discharge print output. It requires a 100% reactive-dyed cotton substrate for a brilliant print outcome.

Mix the Aquagent 100, an additive agent, into the Arbisol DS100 base in order to activate the discharge effect. [★] Such a mixture should be consumed within eight (8) hours to avoid oxidation, after which, the ink shall no longer have discharge effect.

• Soft-hand feel
• Good washing fastness
• Good printability and stability on screen
• Easy cleanup with soap and water

Arbisol DS100 mixed with PRC Red Scarlet.
Arbisol DS100 mixed with PRC Red Scarlet.
Add Arbiair White SC to make white discharge print.
Add Arbiair White SC to make white discharge print.
Prints_Arbisol DS100(02)
Previous image
Next image
  • Application
Direct to textile printing. For cut-piece articles and ready-to-wear.
  • Material Compatibility
• 100% Cotton, reactive-dischargeable dyed substrate
  • Gloss/Luster
Low Gloss
  • Pigment Type
PRC Pigment
  • Emulsion
Photo Flash 300E
  • Screen Mesh in cm
100T – 150T, monofilament
  • Squeegee
Square edge, medium durometer
  • Recommended Curing Parameters
Drying time : 10 seconds
Temperature : 110ºC (230ºF)
Equipment : Heat press/oven/flash cure
Pre-curing : Heat gun
  • Additives
Thickener ASE : 1% – 2%
Reducer CT : 1% – 2%
Aquagent 100: 6% – 10% [★]
  • Browse through our...
Textile Inks
Additives & Auxiliary Chemicals
Accessories

Printing Procedure

1. To achieve good color brilliancy during screen-printing (manual), maintain medium pressure and speed with a 45º to 60º angle. Semi-cure with a heat gun to keep ink dry but not entirely discharged. Discharge print will give a brighter print output when fully cured via heat press, oven, or flash cure machine.
2. The printing process can be done either manual or via automatic screen-printing. Suggested maximum of two [2] strokes, two [2] coats on spot designs and single-color half-tone prints. It is not recommended on CMYK prints.

Cleanup

Wash materials used with soap and water. Observe all local regulations when disposing of this substance.

Storage Condition

Store tightly covered at temperatures between 10ºC – 30ºC (50ºF – 86ºF) and a relative humidity between that of 25% to 70%. Keep away from direct sunlight or high temperatures.

Find the dealer nearest you.

Click Here

Keep scrolling for additional information

Additional Information

Print according to color sequence. A ready-mixed base is recommended to beginners on screen-printing. Otherwise, you can mix the color yourself. Just ensure not to incur over-pigment load.

To achieve a smooth surface print, heat press curing is recommended.

To achieve good color opacity and brilliance during screen-printing (manual), maintain medium pressure and speed with a 45º to 60º angle.

Keep the screen wet by flooding the screen with just the right amount of ink or keep the screen clean.

Important Note

This technical data sheet does not replace the Safety Data Sheet and should be used according to its recommended purpose. Any person using the product other than that specifically recommended does so at his own risk.

While we endeavor to ensure that all recommendations about our products are correct, many factors may affect the application of the product. It is advised that the quality of the substrate, the condition of the curing method, and other printing characteristics brilliance before mass production.

Disclaimer

The information and recommendation in this publication are to the best of our knowledge, information, and belief accurate at the date of publication. Nothing herein is to be construed as a warranty, express or implied.

In all cases, it is the responsibility of users to determine the applicability of such information or the suitability of any products for their own particular purpose. Therefore, we do not accept any liability whatsoever or howsoever arising for the performance of the product or for any loss or damage incurred out of the use of the product.

The information contained herein is liable to modification from time to time in light of continuous product development or improvements.