Menu

Arbiair Matte DC

Packaging: 20K, 4K, 1K, 500g, 250g, 125g

Translucent water-based ink most often used for airbrush painting on colored ground substrates, usually on dark colors.

• Soft-hand feel
• Good washing fastness
• Good printability and stability on screen.
• Easy cleanup with soap and water
• Dual-purpose usage, airbrush and screen-print

  • Application
Arbiair series is compatible with airbrush tool and direct-to-textile printing on cut-piece articles and ready-to-wear outfit.
  • Material Compatibility
• 100% Cotton
• 50/50 Cotton-polyester blend
• 50/50 Cotton-synthetic fiber
• Calico/Canvas
  • Gloss/Luster
Medium Gloss
  • Pigment Type
PRC Pigment
  • Emulsion
Photo Flash 300E
  • Screen Mesh in cm
(For screen-printing) 100T-120T, monofilament
  • Squeegee
Square edge, medium durometer
  • Recommended Curing Parameters
Drying time : 10 seconds
Temperature : 110ºC (230ºF)
Equipment : Heat press/oven/flash cure
Pre-curing : Heat gun
  • Additives
Thickener ASE : 1% – 2%
Reducer CT : Not recommended
Fixer MR15 : 2% – 3%
  • Browse through our...
Textile Inks
Additives & Auxiliary Chemicals
Accessories

Printing Procedure

For Airbrush Procedure
1. Prepare your airbrush/pen tool. Preferably use the double action type for greater control and easy clean, as a single action has less moving parts. Ideally, use at least a 100 P.S.I. air compressor and then prepare your inks and practice controlling atomization.
2. On use of color, clean the airbrush tool to prevent colors from mixing in the airbrush. Blow water out on a rag or a piece of scratch paper.
3. Wash out the airbrush tool immediately after you are done painting. Make sure to disassemble carefully for a sure clean.

For Screen-printing Procedure
1. The printing process can be done either manual or via automatic screen-printing. Suggested maximum of three [3] strokes, three [3] coats, except when printing tonal or CMYK process.
2. In halftone print, one [1] stroke is ideal but two [2] strokes are acceptable, however, one [1] coat only is highly suggested.
3. Curing is recommended to greatly increase washing fastness. Curing will also give the print a glossier print output.

Cleanup

Wash materials used with soap and water. Observe all local regulations when disposing of this substance.

Storage Condition

Store tightly covered at temperatures between 10ºC – 30ºC (50ºF – 86ºF) and a relative humidity between that of 25% to 70%. Keep away from direct sunlight or high temperatures.

Find the dealer nearest you.

Click Here

Keep scrolling for additional information

Additional Information

Print according to color sequence. A ready-mixed base is recommended to beginners on screen-printing. Otherwise, you can mix the color yourself. Just ensure not to incur over-pigment load.

To achieve a smooth surface print, heat press curing is recommended.

To achieve good color opacity and brilliance during screen-printing (manual), maintain medium pressure and speed with a 45º to 60º angle.

Keep the screen wet by flooding the screen with just the right amount of ink or keep the screen clean.

Important Note

This technical data sheet does not replace the Safety Data Sheet and should be used according to its recommended purpose. Any person using the product other than that specifically recommended does so at his own risk.

While we endeavor to ensure that all recommendations about our products are correct, many factors may affect the application of the product. It is advised that the quality of the substrate, the condition of the curing method, and other printing characteristics brilliance before mass production.

Disclaimer

The information and recommendation in this publication are to the best of our knowledge, information, and belief accurate at the date of publication. Nothing herein is to be construed as a warranty, express or implied.

In all cases, it is the responsibility of users to determine the applicability of such information or the suitability of any products for their own particular purpose. Therefore, we do not accept any liability whatsoever or howsoever arising for the performance of the product or for any loss or damage incurred out of the use of the product.

The information contained herein is liable to modification from time to time in light of continuous product development or improvements.
Scroll to Top