0

Cart

0
Subtotal: 0.00
No products in the cart.
0

Your Cart

0
Subtotal: 0.00
No products in the cart.

Keenplas ST Matte

125.00230.00

A translucent plastisol ink ideally for printing directly on white to dark ground substrates.

▪ Soft-hand feel with good washing fastness
▪ Good printability and stability on screen, easier to print
▪ Low cure, phthalate-free ink
▪ Does not clog the screen

  • Application

  • ▪ Direct to substrate textile printing. For cut-piece articles and ready-to-wear.
  • Material Compatibility

  • ▪ 100% Cotton
    ▪ Dominant cotton-polyester blend/synthetic fiber
    ▪ Spandex/dry-fit
    ▪ Calico/Canvas
  • Recommended Curing Parameters

  • Heat Press Machine 10 seconds | 120°C -150°C (248°F – 302°F)
    Oven Type 2-3 minutes | 120°C -150°C (248°F – 302°F)
    Flash Cure 3-5 seconds | 95°C-110°C (203°F – 230°F)
  • Emulsion & Mesh

  • Emulsion: Photoflash SR Series
    Screen Mesh in CM: 12T – 460T, Monofilament
  • Additives

  • KP Viscosity Enhancer 1% – 2%
    KP Viscosity Reducer 1% – 2%
  • Squeegee

  • More Ink Deposit Less Ink Deposit
    Medium (65-75 durometer) Soft (50-60 durometer)
    Hard (80-90 durometer) Round (bull-nose)
    Square (straight edge)
▪ Direct to substrate textile printing. For cut-piece articles and ready-to-wear.
▪ 100% Cotton
▪ Dominant cotton-polyester blend/synthetic fiber
▪ Spandex/dry-fit
▪ Calico/Canvas
Heat Press Machine 10 seconds | 120°C -150°C (248°F – 302°F)
Oven Type 2-3 minutes | 120°C -150°C (248°F – 302°F)
Flash Cure 3-5 seconds | 95°C-110°C (203°F – 230°F)
Emulsion: Photoflash SR Series
Screen Mesh in CM: 12T – 460T, Monofilament
KP Viscosity Enhancer 1% – 2%
KP Viscosity Reducer 1% – 2%
More Ink Deposit Less Ink Deposit
Medium (65-75 durometer) Soft (50-60 durometer)
Hard (80-90 durometer) Round (bull-nose)
Square (straight edge)

Series Description

The special effect ink designed to be the true fashion base. It is the go-to ink designed to attract attention. The series’ various textures and unique print outputs give off a ‘wow’ factor to an otherwise plain surface print.

Cleanup

Wash materials used with soap and water. Observe all local regulations when disposing of this substance.

Storage Condition

Store tightly covered at temperatures between 10°C – 30°C (50°F – 86°F) and a relative humidity between that of 25% to 70%. Keep away from direct sunlight or high temperatures.

Can't find what you need?
Find the dealer nearest you.

Keep scrolling for additional information

Additional Information

Print according to color sequence. A ready-mixed base is recommended to beginners on screen-printing. Otherwise, you can mix the color yourself. Just ensure not to incur over-pigment load.

To achieve a smooth surface print, heat press curing is recommended.

To achieve good color opacity and brilliance during screen-printing (manual), maintain medium pressure and speed with a 45º to 60º angle.

Keep the screen wet by flooding the screen with just the right amount of ink or keep the screen clean.

Important Note

This technical data sheet does not replace the Safety Data Sheet and should be used according to its recommended purpose. Any person using the product other than that specifically recommended does so at his own risk.

While we endeavor to ensure that all recommendations about our products are correct, many factors may affect the application of the product. It is advised that the quality of the substrate, the condition of the curing method, and other printing characteristics brilliance before mass production.

Disclaimer

The information and recommendation in this publication are to the best of our knowledge, information, and belief accurate at the date of publication. Nothing herein is to be construed as a warranty, express or implied.

In all cases, it is the responsibility of users to determine the applicability of such information or the suitability of any products for their own particular purpose. Therefore, we do not accept any liability whatsoever or howsoever arising for the performance of the product or for any loss or damage incurred out of the use of the product.

The information contained herein is liable to modification from time to time in light of continuous product development or improvements.

Scroll to Top